Car Key Button Repair

A damaged car key repair cost key button is frustrating. You may need to contact an emergency locksmith service or purchase a replacement remote.

You could save money by fixing your old key fob instead of replacing it. This is particularly true if an old switch or damaged contacts are the cause of the problem.

Battery

If the buttons on your key fob don't respond to pressing, this could be a clear indication that your battery is dead or nearing the end of its lifespan. It's simple to replace the battery yourself instead of hiring a locksmith or dealership.

Find the battery compartment first. It is usually located on the backside of the key fob. It might be hidden behind an open cover that slides out or an access point that opens when you push a button. Once the compartment is exposed you can see the small button cell battery. It is usually shaped like an ordinary coin and is identified with a plus and minus symbol. Remove the old battery, and replace it with a brand new one. Make sure that the plus and the minus symbols are properly aligned.

Once the battery is installed close the compartment and snap the two parts of the key fob together. Make sure you align the pieces and secure them correctly prior to closing the door and testing your keys. Press any of the buttons to confirm that they work properly.

If the remote keyfob isn't working after replacing the battery, there could be other problems that require a different type of repair. Physical damage from dropping the fob in a puddle, for instance, can sometimes cause it to cease functioning altogether. Alternatively, it might be experiencing an internal electrical failure or it may require to be deprogrammed by an expert or locksmith. Find out if the problem is related to your key fob using these other automotive troubleshooting methods.

Switches

Depending on the year and the make, there are different kinds of switches that are found that are used in the car key fob repair service keyfob. The older style keys have a chip that is visible inside the case. The newer keys work by sending signals to your car. The buttons on a key may be damaged or worn out due to regular use, irrespective of the type. They can become difficult to press or not responsive. If you attempt to force the button to work the button, it could cause damage, and could even prevent the key from being able to start your vehicle in the future.

If your key doesn't appear to be working, you should first try changing the battery. If it doesn't work, you may have to clean the key fob or adjust the switches. These tiny electronic switches are more likely than larger parts of the key to break because they are constantly tossed about.

The switches are made of rubber, and they're coated with an electrically conducting film that is prone to wear out over time. However, they're tiny and cheap to replace. They're soldered to the circuit board, which means it is important to remove the old ones without causing any damage to any other part of the circuit. You can then solder new ones into and then reassemble your fob.

An effective way to protect your car key fob from becoming damaged is to not use it for longer than a couple of hours at a stretch, and to avoid leaving it in visible locations that it will be visible. Also, you should locate a safe place to store your key when you aren't using it.

If the issue continues to persist after you have cleaned your key fob replaced the battery and attempted to clean it, then you may need to consult a locksmith. A professional can check the frequency of your key to determine whether it's still able communicate with your vehicle, open and replace micro switches, change cases, and more.

Outer Case

If the buttons don't move freely up and down the case, they could get stuck or break. If changing the battery or cleaning it with an alcohol-based swab and a cotton pad alcohol rubbing doesn't solve the issue, taking off the case and examining it could be required. If the contacts that the buttons touch aren't fitting well or are worn out, adjusting them might be the only option to fix the problem.

Rubber buttons be worn out over time. Rubber buttons can become difficult to press when they stretch, and nails may cut them. This could cause the key to fail and in this instance it is time for the replacement of the case or buttons. This repair involves disassembling the remote, then locating the button switches on the circuit board, and then heating the solder and carefully removing them. The circuit board is soldered with new buttons. The case can be rebuilt and the key blade of the horseshoe can be inserted. The new buttons must be tightly fitted inside the case to avoid them falling out.

Inner Case

Since your key fob is likely be tossed around and occasionally be pressed by accident and the buttons within can be damaged or stuck over time. If your key fob ceases to function while you are away from home, you can fix the problem quickly by using metallic tape and punch holes. This will allow you to open doors, but not start the vehicle. This simple fix will allow you to safely get back to your car key repair and complete your journey.